車間整體除塵設備的工作原理

Working principle of the overall dust removal equipment in the workshop

　　除塵器的工作原理如下：含塵氣體由下部敞開式法蘭進入過濾室，較粗顆粒直接落入灰倉，含塵氣體經濾袋過濾，粉塵阻留于袋表，凈氣經袋口到凈氣室，由風機排入大氣。當濾袋表面的粉塵不斷增加，程控儀開始工作，逐個開啟脈沖閥，使壓縮空氣通過噴口對濾袋進行噴吹清灰，使濾袋突然膨脹，在反向氣流的作用下，賦予袋表的粉塵迅速脫離濾袋落入灰倉，粉塵由卸灰閥排出。

The working principle of a dust collector is as follows: the dusty gas enters the filter chamber through the lower open flange, and the coarser particles directly fall into the ash bin. The dusty gas is filtered by the filter bag, and the dust is trapped on the bag surface. The clean gas is then transported to the clean gas chamber through the bag mouth and discharged into the atmosphere by a fan. When the dust on the surface of the filter bag continues to increase, the programmable controller begins to work. Pulse valves are opened one by one, allowing compressed air to spray and clean the dust on the filter bag through the nozzle, causing the filter bag to suddenly expand. Under the action of reverse airflow, the dust on the bag surface quickly separates from the filter bag and falls into the ash bin, and the dust is discharged by the ash discharge valve.

　　濾筒除塵器工作原理：含塵氣體進入除塵器灰斗后，由于氣流斷面突然擴大及氣流分布板作用，氣流中一部分粗大顆粒在動和慣性力作用下沉降在灰斗；粒度細、密度小的塵粒進入濾塵室后，通過布袋擴散和篩濾等組合效應，使粉塵沉積在濾袋表面上，凈化后的氣體進入凈氣室由排氣管經風機排出。

Working principle of filter cartridge dust collector: After the dusty gas enters the ash hopper of the dust collector, due to the sudden expansion of the airflow cross-section and the action of the airflow distribution plate, some coarse particles in the airflow settle in the ash hopper under the action of dynamic and inertial forces; After the fine particle size and low density dust particles enter the dust filter room, they are combined with bag diffusion and screening to deposit the dust on the surface of the filter bag. The purified gas enters the clean air chamber and is discharged by the exhaust pipe and fan.

　　濾筒式除塵器的阻力隨濾袋表面粉塵層厚度的增加而增大。阻力達到某一規定值時進行清灰。此時程序控制電磁脈沖閥的啟閉，首先一分室提升閥關閉，將過濾氣流截?cái)啵缓箅姶琶}沖閥開啟，壓縮空氣以及短的時間在上箱體內迅速膨脹，涌入濾筒，使濾筒膨脹變形產生振動，并在逆向氣流沖刷的作用下，附著在濾袋外表面上的粉塵被剝離落入灰斗中。

The resistance of the filter cartridge dust collector increases with the increase of the thickness of the dust layer on the surface of the filter bag. Clean the dust when the resistance reaches a certain specified value. At this point, the program controls the opening and closing of the electromagnetic pulse valve. Firstly, the lifting valve of the first chamber is closed to cut off the filtered air flow. Then, the electromagnetic pulse valve is opened, and compressed air and a short period of time rapidly expand inside the upper chamber, flowing into the filter cartridge, causing the filter cartridge to expand and deform, resulting in vibration. Under the action of reverse airflow erosion, the dust attached to the outer surface of the filter bag is peeled off and falls into the ash hopper.

　　清灰完畢后，電磁脈沖閥關閉，提升閥打開，該室又恢復過濾狀態。清灰各室依次進行，從第一室清灰開始至下一次清灰開始為一個清灰周期。脫落的粉塵掉入灰斗內通過缷灰閥排出。

After the ash cleaning is completed, the electromagnetic pulse valve is closed, the lifting valve is opened, and the room returns to the filtering state. The cleaning process is carried out sequentially in each room, with one cleaning cycle from the first cleaning to the next cleaning. The detached dust falls into the ash hopper and is discharged through the ash discharge valve.

以上就是有關：車間整體除塵設備  的介紹，想了解更多的內容請點擊：http://www.52campus.cn 我們將會全心全意為您提供滿分服務，歡迎您的來電！

The above is an introduction to the overall dust removal equipment in the workshop. To learn more, please click: http://www.52campus.cn We will wholeheartedly provide you with full score service. Welcome to call us!

上一篇：車間整體除塵設備的分類有哪些？
下一篇：多工位焊煙除塵設備的常見分類